JERAJournal of Electronic Research and Application2208-35022208-3510Bio-Byword Scientific Publishing Pty. Ltd.10.26689/jera.v9i2.10156ArticleStudy on Preparation and Forming of TiC Steel-Bonded Cemented Carbide Paste for Direct Writing Printinghttps://artdesignp.com/journal/JERA/9/2/10.26689/jera.v9i2.10156WangZhi,XuBing,YuanJiawei,ChengXiang Jie,YueTing Pu,ZhangMei Ye,ZhouSheng Hui2025922025-04-10TiC steel-bound cemented carbide body was prepared by direct writing printing. The effects of powder content (89.28, 89.49, 89.69, 89.88, and 90.07 wt%) and dispersant content (0.017, 0.034, 0.051, and 0.068 wt%) on the slurry and printing body were studied. The experimental results show that with the increase of powder content, the viscosity of the slurry gradually increases, the settlement rate gradually decreases, and the size and linewidth of the blank body gradually decreases. When the powder content is 89.69 wt%, the sedimentation stability and extrusion stability of the slurry are the best, and the density of the blank body is the highest, which is 3.8275 g/cm3, which is suitable for direct writing printing. The addition of dispersant reduced the viscosity of the slurry; With the increase of dispersant content, the surface line width and size of the printed body gradually increased. When the dispersant content is 0.034 wt%, the extrusion stability of the slurry is the best, and the density of the body is the highest, which is 3.8901 g/cm3.

Zheng J, Zhao Z, Liu X, et al., 2018, Effect of Nano-composite Inhibitor on the Composition and Microstructure of WC-TiC-Co Cemented Carbide Prepared by Microwave Method. Powder Metallurgy Industry, 28(04): 21–25.

Li G, Chen W, Sun L, et al., 2017, Microstructure and Properties of TiC Steel-bonded Carbide Used Fe/Mo Pre-alloyed Powder as Binder. Materials Science Forum, 898: 1459–1467.

Chen Z, Li Z, Liu C, et al., 2018, 3D Printing of Ceramics: A review. Journal of the European Ceramic Society, 39(4): 661–687.

Guo Y, 2008, Metal Cutting Liquid Pollution and Green Cutting Technology. Sci-Tech Information Development and Economy, 18(36): 84–85.

Alexander S, Egmont R, Tinus S, et al., 2023, SLA-printed K-band Waveguide Components using Tollens’ Reaction Silver Plating. IEEE Transactions on Components, 13(2): 230–239.

Mustafa K, Volkan_K, Tugce T, et al., 2023, Three-dimensional Printability of Bismuth Alloys with Low Melting Temperatures. Journal of Manufacturing Processes, 92: 238–246.

Ferro P, Fabrizi A, Berto F, et al., 2023, Creating IN718-high Carbon Steel Bimetallic Parts by Fused Deposition Modeling and Sintering. Procedia Structural Integrity, 47: 535–544.

Giovanni P, Chiara G, Paolo C, et al., 2016, Direct Ink Writing of Micrometric SiOC Ceramic Structures using a Preceramic Polymer. Journal of the European Ceramic Society, 36: 1589–1894.

Liu K, Lei Q, Zhang Y, et al., 2023, Additive Manufacturing of Continuous Carbon Fiber-reinforced Silicon Carbide Ceramic Composites. International Journal of Applied Ceramic Technology, 20(6): 3455–3469.

Rios J, Zambrano R, Taborda J, et al., 2023, Process Parameters Effect and Porosity Reduction on AlSi10Mg Parts Manufactured by Selective Laser Melting. The International Journal of Advanced Manufacturing Technology, 129(7): 3341–3351.

Cao J, Wang Pei, Liu Z, et al., 2022, Research Progress on Powder-based Laser Additive Manufacturing Technology of Ceramics. Journal of Inorganic Materials, 37(3): 241–254.

Zhang Y, Zhang Y, Chen Y, et al., 2022, Effect of Microwave on Mechanical Properties of Laser-sintered Carbon Nanotube-polymer Composites. Materials Science and Technology, 38(15): 1239–1243.

Liu Y, Cheng Y, Ma D, et al., 2022, Continuous Carbon Fiber Reinforced ZrB2-SiC Composites Fabricated by Direct Ink Writing Combined with Low-temperature Hot-pressing. Journal of the European Ceramic Society, 42(9): 3699–3707.

Zhang X, Guo Z, Chen C, et al., 2018, Additive Manufacturing of WC-20Co Components by 3D Gel-printing. International Journal of Refractory Metals and Hard Materials, 70: 215–223.

Ruoyu C, Adam B, Joshua R, et al., 2022, Additive Manufacturing of Complexly Shaped SiC with High Density via Extrusion-based Technique-Effects of Slurry Thixotropic Behavior and 3D Printing Parameters. Ceramics International, 48(19): 28444–28454.